To obtain a position in the field of Mechanical Engineering and apply my knowledge, professional experience in FEA Engineer Experience on Finite Element Analysis of stress analysis, fatigue, heat transfer analysis; general contact generation, boundary condition and load generation by using Abaqus; hex, tetra mesh generation, model defeatured, model preprocessing by using Hypermesh; optimization by using Optistruct, S-N curve, fatigue analysis, life cycle by using Fe-Safe and 3-D modeling by using SolidWorks Proficient at knowledge of mechanics of material, stress calculation, force analysis, material property, theory of elasticity, fatigue theory, etc. Test Supervisor, Assistant Engineer certificated Years of debugging and testing experience in energy industry Leadership, teamwork, management, self-motivated, problem solving ability and ready for challenges
Skills
FEA Software: Abaqus/CAE, Hypermesh, Optistruct, Fe-Safe, Simlab
*CFD Software: Star CCM+
*CAD Software: SolidWorks
*PC: Windows, Excel, PPT, Words
Professional Experience
China Nuclear Power Engineering Corporation LimitedJanuary 2011 to May 2013Test Supervisor
Investigation and Solution to the Problem that Electrically Operated Valve Cannot Be Closed Tightly in China Nuclear Power Engineering Co., Ltd.
02/2013 In operation period, electrically operated valve sometimes cannot be closed 100% tightly, reasons and solutions are as follows: firstly, in winter, ice in valves could generate this problem, so heat insulator was recommended; secondly, in the period of debugging, about 5% allowance of closing magnitude should be considered, in addition, electrically operated valve and manual handle should be used cooperatively Lift Force, Drag Force, Moment Distribution on Airfoils (CFD) in Syracuse University, 03/2014 Used wind tunnel, airfoils to find out how lift, drag and moment of airfoils (NACA0012 and NACA0015) change with angle of attack; measured data of NACA0015 airfoil by using pressure transducers and NACA0012 airfoil by using force balance scale; determined the influence of Reynolds Number on the experiment result by using two different velocity; discussed the influence of Three Dimensionality on experiment result by comparing test data and database of NACA airfoil Obtain Max Shear Stress of 3-D Steel Bar by Using ANSYS (FEA) in Syracuse University, 04/2014 Given that a 3-D model with rectangular cross section was exerted by shear stress; material of the model was steel, Young's Modulus and Poisson's Ratio were given; 3-D model was created by using SolidWorks; 3-D tetra mesh, boundary condition, load was generated by using ANSYS, analyzed and summarized the reason of location of max shear stress.
Dalian Thermoelectric Group Corporation LimitedJuly 2009 to January 2011Assistant Engineer
Patrolled turbine system including steam turbine, condenser, heater at regular time to make sure no abnormal conditions happened Reported problems, like mechanical problem, excessive noise and vibration, pipeline leakage, etc.
to superior, supported root cause analysis and issue solution Cooperated Maintenance Department to repair machine, pump, pipeline, rivet by using wrench, screwdriver, pipe wrench, lifting jack, etc.
System Debugging Experiences Test, Debugging of Sea Water Desalination System in China Nuclear Power Engineering Co., Ltd.
Static verification; dynamic verification with electricity; dynamic verification with medium Make and break test of motor driven valve, adjustment of valve Test and debugging of dosing system, to guarantee the normal operation of system and dosage, etc.
Test, Debugging of Hydrogen Generation System in China Nuclear Power Engineering Co., Ltd.
Hydrostatic test of cooling water pipeline, electrolytic cell pipeline, etc.
Debugging and test of Programmable Logic Controller.
China Nuclear Power Engineering Corporation LimitedJune 2012Test Supervisor
Dalian Thermoelectric Group Corporation Limited FEA/ CAE TrainingApril 2010Assistant Engineer
Instructed by a FEA manager who works for an automotive supplier company in Detroit ABAQUS, the control of convergence, general contact, linear/nonlinear analysis, static stress analysis, applied to bolt, flange, universal joint, differential case, crash, etc.
HyperMesh, preprocessing of 2D, 3D model; tetra, hex mesh generation, etc.
OptiStruct, topology optimization; smoothing and interpretation of optimization results, etc.
Fe-Safe, fatigue analysis, S-N curve, life cycle, etc.
Education and Training
Syracuse University, L. C. Smith College of Engineering and Computer Science12/2014Master of Science: Mechanical and Aerospace EngineeringSyracuse, NY, USAMechanical and Aerospace Engineering
Northeast Dianli University, College of Energy and Mechanical Engineering07/2008Bachelor of Science: Thermal Energy and Power EngineeringJilin, ChinaThermal Energy and Power Engineering Finite Element Analysis (FEA), Computational Fluid Dynamics (CFD), Advanced Mechanics of Material, Fluid Mechanics Measurement, Fluid Dynamics, Turbulence, Advanced Methods of Analysis, Modeling and Optimization, Principle of Wind Turbine, Advanced Thermodynamics
*Undergraduate: Mechanical Drawing, Heat Transfer, Engineering Mechanics, Electric Engineering, Automation, Principle of Turbine, Principle of Boiler
Languages
Native Mandarin, fluent in oral and written English
Interests
Kart Racing, Snooker, Soccer, jogging, Music
Additional Information
Interests: Kart Racing, Snooker, Soccer, jogging, Music
