Global Technology Leader Resume Example Park Place Technologies

GLOBAL TECHNOLOGY LEADER

Summary

ENGINEERING PROFILE ELECTRICAL POWER SYSTEM / ELECTRO-MECHANICAL / RENEWABLE ENERGY SYSTEMS Electrical Power System /Testing, Field Service/Building System , Electrical Distribution System &Design. Engineering professional who combines broad-based expertise in electro mechanical systems, System test, renewable energy, electrical power converters/inverters for renewable energy Generators/power conversion technology, UPS power distribution systems, energy storage system and controls, skilled in identifying and correcting problems to component level in a variety of electrical and mechanical systems. Proficient in troubleshooting power distribution systems, High/Medium voltage equipment/quality assurance, designing electrical distribution circuits. In-depth knowledge of building codes with special emphasis on national electric code/NFPA 101/70B/70Es. A self-motivated team player who works well in a team environment or as an individual contributor with a "do what it takes attitude". Proficient in PC/Micro station CAD, Microsoft Office, Maximo, SAP, Outlook, Staraio and Aspen. AREAS OF EXPERTISE Reading Blueprints , Engineering Prints/Schematic Drawings to analyze electrical circuits and equipments Traffic Engineering Technology Computer Network Technology Power Conversion Technology Renewable Energy Power/Controls Solar,Wind Battery,Rectifiers etc) Power System Scheme(on/off) grid Powper.System Applications Oscilloscopes/Power analyzers Thermographic survey (Infrared), Short Circuit/coordination studies Low/Med/High(480-500,000 Volts) Failure Analysis/ Root Cause Breakers & Switch-gears Power meters/IQs Arc flash hazard analysis Arc flash boundaries Incident energy level Required level of PPE/ Awareness Protective devices/ Coordination Electrical Standards -UL1741,NEC, ANSI,1EEE1547. GID(Grid Isolation Disconnect) ECM(Energy Comm. Master) Substation, Excitation Equipment Dry/Oil fill transformer Testing Transformer Low/Medium/High voltage Circuit Breakers Medium Voltage Control/Drives/Startups HV breakers and transformer test Power System Technology Testing/Installation of AC/DC Drives/Motor Power Supply Designs/ monitoring hardware/software Process Studies, Investigations Primary/secondary distribution Switchgears/ Controls Equipment Motor Control Centers (MCC) Power Electronic Circuits High voltage/current injection UPS/Emergency generators Protective Relays, Power Cables.

Experience

Electrical Test Engineer/Manager
October 2012 to CurrentPark Place Technologies － Atlanta , GA

Supervised Lower level Engineers and Technicians in developing Electrical specification and testing AC/DC Power control units (AC/DC PCU) and power converter/inverters for energy storage systems.
renewable energy systems.
Lead in designing and testing all systems/calculations, coordinate test procedures/data collection, testing in areas of power and controls, both in product and system levels.
Manage and technically lead in test area projects, budget/schedule design projects to meet or exceed expectations.
Direct other lower level Engineers/Technicians in developing documentation and provide the review and approval of all electrical documentation.
Write/developed test plans, Certified test reports (CTR), standard Operating procedures (SOP) for Performing the "FAT" test using standard company's specification as reference standard.
Test and trouble shoot the High voltage DC/DC converters, DC/AC inverters, entire power control units and V3s energy storage system used for renewable energy System during.

High Voltage Test Engineer/Supervisor
May 2011 to October 2012

Supervised Lower level Engineers and Technicians in testing High/medium voltage cable using High voltage Resonance Test System, Dielectric DC Test Set, Megger Insulation Test setT, High voltage /High current injection Test set, Omicron Test set, Doble (F6150) Test set and digital Low resistance Ohmmeter (DLRO) etc.
Write/developed test plans, Certified test reports (CTR), standard Operating procedures (SOP) from Customer's and standard company's specification, utilizing shop orders/CDAs as reference standard.
Assisted quality specialist in developing/upgrading CTRs/CDAs to ensure that it's in compliance with AEIC CS9 and Insulated Cable Engineers Association ( ICEA S-108-720).
Directed/participated with lower level Engineers and Technicians in performing: Partial discharge test on Cables utilizing (Resonance and Cable Test Termination/WC method.
AC withstand test on high voltage Cable utilizing (Resonance and Cable Test Termination/WC method).
Insulation Power factor and Tan delta test utiliz.

Field Service Engineer
July 2007 to May 2011NA － City , STATE

Commissioned, maintained and provided emergency support on power electrical and electronics at customers' sites.
Performed design reviews, prepared test procedures and reports, coordinated and oversaw on-site testing.
Provided preventive maintenance, emergency response, equipment start-up and field modifications.
Performed inspections, maintenance and repairs on electrical substations and transformers, low to high voltage switch gears/ motor control centers, including Hipot, insulation resistance and over-potential tests.
Conducted primary and secondary injection test on low voltage/low voltage power circuit breakers and medium voltage breakers, including contact resistance, insulation resistance, over-potential and integrity tests.
Performed thermo graphic survey (Infrared Scan)/NEC & OSHA review on all switch gears, distribution panels, utility transformers, incoming section of switch gears, breakers and cables.
Pinpointed potential hazards.
Tested Dry/Oil fill transformers and troubleshoot medium vo.

Senior System Tester/QA
February 2005 to July 2007EATON CORPORATION Electrical Services & Systems － City , STATE

Performed multi-module testing of UPS units and testing of multi-module system with SBMs.
Recommended modifications and improvements to enhance products for quality/ reliability.
Reviewed customer specifications and selected proper material to satisfy the specification.
Provided technical direction to technicians, and assisted both internal and external customers.
Evaluated product design failures and helped determine ways to correct failures Visited various customers' sites to provide support on technical problems/installations.
Provided technical support to other branches both domestic and abroad.
Perform routine on Dry type/Liquid immersed transformers in accordance with IEEE standards as approved by ANSI procedures, and some design test (usually impulse test) on special requested.

Building Systems Engineer II
January 1999 to February 2005EATON CORPORATION/P － City , STATE

Reviewed plans and specifications for new and existing constructions, such as Hospitals, Nursing homes and Ambulatory Surgical Centers, to insure compliance with the state and federal regulations for physical plant and life safety standard.
Cross trained in the areas of Electrical Engineering, Mechanical Engineering and Architectural Engineering.
Performed on site inspection of new facilities and renovation or additions to existing facilities to determine compliance with approved plans and specifications.
Promoted building code with special emphasis on National Electric Code/NFPA.
Reviewed and utilized client documentation during inspection process (drawings, studies, maintenance logs, etc.).
Developed cost estimates for facilities replacement costs and corrective measures.

Traffic Electrical Engineering Tech. IV
December 1996 to December 1998STATE OF NORTH CAROLINA DFS － City , STATE

Utilized PC / Microsoft office and Micro station (CAD) Intergraph to perform duties such as designing electrical distribution circuit details for new and up-grading signals.
Assisted in reviewing specification/developed documentation for scratch requisitions.
Assisted in providing technical support to all fourteen highway divisions of traffic engineering branch.
Used various manufacturers' cabinet prints and drafting tools to amend systems to match specification.

Global Technology Leader
STATE OF NORTH CAROLINA DOT － City , STATE

Energy Storage And Renewable Energy Systems.

Education

BSEE : Electrical EngineeringNorth Carolina A&T State University － City, State

Computing Technology Industry Association(CompTIA), CISCO Certified Network Associate(CCNA), Thermal/Infrared Thermography, Level II, Osha General Industry Safety Program-2012. Eaton Certified Field Service Engineer(Basic/Advanced Electrical Testing, Electrical Equipment Maintenance, Motor controls, Drives/Starters & Electrical Arc-Flash Safety).

Resume Overview

School Attended

North Carolina A&T State University

Job Titles Held:

Electrical Test Engineer/Manager
High Voltage Test Engineer/Supervisor
Field Service Engineer
Senior System Tester/QA
Building Systems Engineer II
Traffic Electrical Engineering Tech. IV
Global Technology Leader

Degrees

BSEE : Electrical Engineering
Computing Technology Industry Association(CompTIA), CISCO Certified Network Associate(CCNA), Thermal/Infrared Thermography, Level II, Osha General Industry Safety Program-2012. Eaton Certified Field Service Engineer(Basic/Advanced Electrical Testing, Electrical Equipment Maintenance, Motor controls, Drives/Starters & Electrical Arc-Flash Safety).

Global Technology Leader Resume Example

DISCLAIMER

How this resume score could be improved?

Resume Overview

Create a job alert for [job role title] at [location].

Similar Resumes