Electrical & Instrumentation Qa Qc Engineer resume example

SITE DEVELOPMENT OF PARKS IN JALMUDAH JUBAIL PROJECT# 691-C23  ROYAL COMMISSION FOR JUBAIL AND YANBU

• Responsible for all electrical inspections related to installation, testing, and commissioning.
• Responsible for preparing QMS documents.
• Responsible for conducting the inspection of all ongoing activates for electrical installation.
• Responsible for preparing the method of statement and ITP’s for all electrical activates.
• Responsible for raising RFI and conducting all the electrical inspection with client Representative.
• Responsible for conducting the inspection of all electrical material before storage, installation and after installation.
• Responsible for raising NCR and initiating corrective action if the work was done is not as per Specification, Method Statement or as per approved shop drawing.
• Report to the Project Manager any deficiencies in the operation of Quality Management & Control System.
• Responsible for ensuring that the work was done is as per Project Specification, Method Statement and as per approved shop drawings. Also to ensure that all approved and inspected materials are used.
• Responsible for reviewing the IFC drawings and inspection documents and ensuring to comply with the Royal commission requirements.
• Preparing daily and weekly  QA/QC reports for ongoingly activates.
• Responsible for ensuring all activates are as per IFC drawing and RC standards.
• Responsible for ensuring all the testing equipment are calibrated.
• Responsible for performing all the required test for LV, MV cable, and Equipment before and after installation.
• Responsible for preparing the hand over documents O&M manuals.

PROJECT: ALMARINA DEVELOPMENT PROJECT

• Responsible for all electrical inspections related to installation, testing, and commissioning.
• Responsible for conducting the inspection of all ongoing activates for electrical installation.
• Responsible for preparing the method of statement and ITP’s for all electrical activates.
• Responsible for raising RFI and conducting all the electrical inspection with client Representative.
• Responsible for conducting the inspection of all electrical material before storage, installation and after installation.
• Responsible for raising NCR and initiating corrective action if the work was done is not as per Specification, Method Statement or as per approved shop drawing.
• Report to the Project Manager any deficiencies in the operation of Quality Management & Control System.
• Responsible for ensuring that the work was done is as per Project Specification, Method Statement and as per approved shop drawings. Also to ensure that all approved and inspected materials are used.
• Responsible for reviewing the IFC drawings and inspection documents and ensuring to comply with the Client requirements.
• Preparing daily and weekly  QA/QC reports for ongoingly activates.
• Responsible for ensuring all activates are as per IFC drawing and RC standards.
• Responsible for ensuring all the testing equipment are calibrated.
• Responsible for performing all the required test for LV, MV cable, and Equipment before and after installation.
• Responsible for preparing the hand over documents O&M manuals.

• Routine & Type testing of all LV Control Panels according to IEC & BS Specifications.
• Routine & Type testing of Power Transformers.
• Routine & Type testing of Instrument Transformers.
• Testing of MCC panels fix and withdraw able circuits.
• Testing of ATS panels.
• Testing of Power Factor Improvement Panels.
• Required rectification of any fault in the product during testing.
• Attending the Inspectors from any pertient concern/department.
• Preparation of Testing Reports/Inspection Calls.
• Quality Control of all accessories used in LV Control Panels And reported any breaches.
• Site commissioning of Power and control panels.
• Primary and secondary current injection.
• Over voltage, over current ,over frequency relays testing.
• Circuit breaker testing MCB,MCCB,ACB.
• Insulation resistance test for LV & MV cables.
• Continuity test for LV,MV cables and instrumentation wires.
• Programming of ZELIO PLC from Schneider electric.
• Short circuit calculation using Ecodial software from Schneider electric.
• Testing and commissioning of LV panels.
• Preparation of RFI with coordination with Clint.
• Provide guide line about safety during testing & commissioning to electricians.

• Managing overall activities pertaining to erection, testing, commissioning and Maintenance of a wide range of Electrical equipment like Transformers, Generators, Motors, Cranes, VFD & Servo drives, Allen Bradley SCADA / PLC.
• Systems and process control & Instrumentation equipment Supervising the functions of troubleshooting & predictive/preventive maintenance for identifying areas of obstructions and reducing machinery downtime to a minimum.
• Executing cost saving and energy saving techniques/ measures and modifications to achieve a substantial reduction in O&M expenditures and work within the budget.
• Planning and undertaking scheduled maintenance Responding to breakdowns.
• Diagnosing faults.
• Repairing equipment.
• Obtaining specialist components, fixtures or fittings.
• Managing budgets.
• Maintaining statistical and financial records.
• Ensuring compliance with health and safety legislation Creating maintenance procedures.
• Managing stocks of supplies and equipment.
• Reported on progress at weekly team meetings.
• Monitored the manufacture of electrical devices and operations to ensure compliance with safety protocols.
• Rendered technical drawings and electrical systems specifications that exceeded company standards.
• Performed load calculation for sizing wire and circuit protection.
• Applied principles of electrical theory to advance and improve product development and efficiency.
• Continually improved methods and procedures for processes, measurement, documenting and work flow techniques.

• Two months training on basics of communication Through optical fiber DRS And new.
• ZTE communication system and also the study of battery system.

• Three months experience and technical training in KOT ADDU power plant Multan.