Structural Engineer Resume Example
Love this resume?Build Your Own Now
STRUCTURAL ENGINEER
Experience
Structural Engineer
May 2016 to September 2016Wsp － Philadelphia , PA
May 2016 to September 2016Wsp － Philadelphia , PA
- Under supervision of senior designer, design various types of steel and concrete structures and prepared structural drawings and specifications including framing and foundations plans, sections, connections and details using Auto-CAD and REVIT.
- Performed structural analysis and design using RISA for different multistory residential and commercial buildings Worked on design foundations, joist girder, truss, column and calculate snow and wind load using ASCE Gained more understanding of governing codes and regulations (AISC, ACI, IBC, IRC and client specific).
Graduate Research Assistant
August 2015 to May 2016Partners Healthcare System － Camden , ME
August 2015 to May 2016Partners Healthcare System － Camden , ME
- Worked on TXDOT's major research project title shear behavior of synthetic fiber reinforced concrete (SYN- FRC) by using JSCE G-553 test method Performed shear test, flexure and compressive behavior of concrete determined based on ASTM C1609 and ASTM C39 respectively Investigate the effect of different concrete compressive strengths on material properties of synthetic fiber- reinforced concrete, two different compressive strengths, 28MPa(4000psi) and 34MPa(5000psi) were used.
Civil Engineer 1
August 2013 to October 2014MAS Constructions M&A Associates| Hyderabad India
August 2013 to October 2014MAS Constructions M&A Associates| Hyderabad India
- Worked on multistory residential and commercial projects by determining the basic geometry and assisted designers in selection of structural type Performing and checking bridge design calculations and plans using manual and software methods for projects and preparing technical reports Compiled bridge design calculations submittal for prime consultant Developed and detailed drawings using Microstation Planned and oversaw the successful execution of various stages of the project in accordance with the contract drawings and specifications and per project QA/QC standards and safety requirements Prepared and processed project documentation including daily reports RFI's and RFP's.
Accomplishments
- 1.
- Harris County SH 288 Toll Lanes Project, Pretensioned Bridge Design, Houston, Texas The Purpose of this project was to develop an understanding of economic design for a Pre-Tensioned Prestressed concrete bridge using TxDOT I-Girders.
- Harris County SH 288 Toll Lanes Project alignment was used to complete the study.
- Various options with different girder types were modeled in PGSuper for design and analysis to make a comparison of girder weights, number of girders and number of strands for final design 2.
- Four-Story Hospital Building, Structural Design, Oklahoma The Project included Reinforced Concrete Design of Structure.
- Reinforced Concrete Slab, Beams, Columns, Foundation and Staircase was Designed.
- Construction drawings and re-bar Details were also provided for all the members designed 3.
- Three-Story Masonry Building, Structural Design, Oklahoma The Project consisted Design of the Theater Building.
- The critical wall was designed as reinforced masonry to take care of gravity and lateral loads.
- Shear design was also completed for the walls.
- Reinforced masonry Column was designed for moments and axial loads.
- Floor and roof system was designed as Reinforced concrete beam and slab system The Design codes and standards used for the project were Building Code Requirements and Specifications for Masonry Structures (TMS 40213/ ACI 53013 / ASCE 513) and Specification for Masonry Structures (TMS 60213 / ACI 530.113 / ASCE 613) 4.
- Two-Story Timber Building, Structural Design, Arlington, Texas Project included a two-story wood-framed Office building.
- It consisted of roof trusses, plywood roof sheathing and stud walls with plywood sheathing, plywood floor sheathing, floor joists, a glulam floor girder, wood columns supporting the floor beam and stairs leading from the ground floor to the second floor 5.
- Design of a Bridge Abutment, Foundation Analysis and Design The project comprised of designing an Abutment wall for a six (06) lane bridge with a total width of 25m.
- The purpose of the Project was to determine the size of abutment wall for stability against sliding and overturning forces.
- Settlement analysis and slope stability analysis was also performed.
- An alternate design was also proposed with piles CBEAR was used for computing bearing capacity and cross checked by hand calculations CSANSET was used to estimate the settlement in sand layer below footing Driven Piles was used to design the piles as alternate Design.
Education
Master of Science : Construction Management, December 2017University of Texas － City, StateConstruction Management GPA: 3.5
Master of Science : Structural Analysis and Design, May 2016University of Texas － City, StateStructural Analysis and Design GPA: 3.3
Bachelor of Science : Civil Engineering, May 2013Osmania University － City, IndiaCivil Engineering GPA: 3.7
Summary
Seeking a challenging Structural/Civil Engineer position for efficient utilization of my Knowledge and Skills gained from
earning Double Master of Science degrees in Civil Engineering Majors and my past work experience
Highlights
| Reinforced Concrete, Prestressed Concrete, Timber, Steel, Masonry Analysis: Finite Element, Structural, Foundation Codes: ACI 318-11, ACI- 440.2R, ASCE 7-10, AASHTO LRFD -14, AISC Steel Construction Manual 14th Edition. NDS; MSJC ; IBC and IRC Programs: Auto CAD, MicroStation 3D Design, SAP2000, STAAD Pro v8i, Etabs, Risa 3D, PGSuper, RCPier ADAPT PT, Timber Works, Primavera P6, Timberline, VU 360, MATLAB, Mathcad, MS Office |
Skills
3D, 3D Design, Auto CAD, Auto-CAD, basic, consultant, client, documentation, framing, Masonry, Mathcad, MATLAB, MS Office, 2000, Works, MicroStation, NDS, Primavera, prime, QA, research, REVIT, RFI, RFP, safety, SAP, supervision, Timberline, type
Additional Information
- HONORS AND ACHIEVEMENTS Awarded a Scholarship from civil research department during Master's program for excellent academics Awarded Telangana scholarship from government of India for the four years of undergraduate study Student member: ASCE, SEI, AISC, AWC, TMS Deans International student award
DISCLAIMER
Resumes, and other information uploaded or provided by the user, are considered User Content governed by our Terms & Conditions. As such, it is not owned by us, and it is the user who retains ownership over such content.
How this resume score could be improved?
Many factors go into creating a strong resume. Here are a few tweaks that could improve the score of this resume:
Resume Strength
- Completeness
- Formatting
- Word choice
- Length
- Measurable results
- Strong summary
- Typos
Resume Overview
School Attended
- University of Texas
- Osmania University
Job Titles Held:
- Structural Engineer
- Graduate Research Assistant
- Civil Engineer 1
Degrees
- Master of Science : Construction Management , December 2017
Master of Science : Structural Analysis and Design , May 2016
Bachelor of Science : Civil Engineering , May 2013
Similar Resumes
